AP-12.5Y Automatic Device for Multichannel Pipette Calibration

The AP-12.5Y is designed to calibrate multichannel pipettes starting at 10 μl. The device features a readability [d] of 0.01 mg and can calibrate up to 12-channel fixed-volume and variable-volume pipettes.

Because the pipette calibration on the AP-12.5Y is fully automatic, it is four times faster. The calibration procedure for a 12-channel pipette takes less than 20 minutes, not six hours, on this instrument.

When purchasing the AP-12.5Y, you get:

two calibrated sensors: THB S and THB W,
two weighing pans: standard, and for balance test and calibration,
two pumps: a single-channel pump and a four-channel pump

The ergonomic design of the AP-12.5Y makes it possible to empty weighing vessels, and their overfilling is signalled by Ambient Light. When calibrating a multichannel pipette, a four-channel pump is used to simultaneously remove water from four vessels, greatly reducing the time required for pipette calibration.

After emptying a 12-channel pipette, the AP-12.5Y checks all channels in a single cycle. In addition to a database of pipette calibration reports, the AP-12.5Y includes a database of pipettes that is editable and contains maximum permissible error values according to ISO 8655. The report database, in turn, contains measurements and error values calculated for individual points and volumes. The user determines the format and content of the reports.

The AP-12.5Y monitors the ambient conditions using calibrated sensors: THB S (ambient conditions measurement) and THB W (liquid temperature measurement), in accordance with ISO 8655. To calibrate the device with mass standards, the weighing pan must be replaced with a pan dedicated to checking and calibrating the balance (both are included in the standard equipment).

The AP-12.5Y can calibrate not only 12-channel pipettes, but also single-channel pipettes.

Datasheet

Maximum capacity [Max]	52 g
Readability [d]	0.01 mg
Tare range	-52 g
Standard repeatability [5% Max]	5 µg
Standard repeatability [Max]	10 µg
Standard minimum weight (USP)	10 mg
Standard minimum weight (U=1%, k=2)	1 mg
Linearity	±0.03 mg
Stabilization time	4 s
Adjustment	internal (automatic)
Typical measurement time for a 12-channel pipette with constant volume, according to ISO 8655 (for d=10 µg)*	Poniżej 20 minut
Typical measurement time for a 12-channel pipette with variable volume, according to ISO 8655 (for d=10µg)*	Poniżej 60 minut
Display	10″ graphic colour touchscreen
Weighing pan dimensions	ø26 + automat
Packaging dimensions	605×560×775 mm
Net weight	17 kg
Gross weight	30 kg
Communication interface	2×USB-A, USB-C, HDMI, Ethernet, Wi-Fi^®, Hotspot
Operating temperature	+10 – +40 °C
Operating temperature change rate	±0.3 °C / 1 h (±1 °C / 8 h)
Relative humidity	20% – 80%
Relative humidity change rate	±1% / h (±4% / 8 h)

*Depends on room conditions and user competence.

360°

Videos

AP-12.5Y Automatic Device for Multichannel Pipette Calibration – Unpacking and Installation (Tutorial)

New Menu Language in 5Y Series Balances: Japanese

AP-12 Automatic Calibration of Multichannel Pipettes in Your Hands

AP-12.5Y – Speed, Process Automation, Cost Reduction

ELLIPSIS – New Balance by RADWAG

ELLIPSIS – Cutting Edge, Innovative, New

Talk to it. Voice Commands in New ELLIPSIS Balance by RADWAG

310 ELLIPSIS – Scan or Tap to Log In

Remote VPN Support on ELLIPSIS Balances

ELLIPSIS – Unlimited Connections

AP-12.5Y Quick and Easy Single-Channel Pipettes Calibration (Tutorial)

AP-12.5Y Quick and Easy Multi-Channel Pipettes Calibration (Tutorial)

AP-12.5Y Quick and Easy Checking and Calibrating (Tutorial)

Functions

Autotest

Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.

Statistics

Statistiscs function registers and analyses performed measurements. This supplies the user withthe following information: Max and Min standard deviation, average value, variance, range et.

IR sensors

Programmable function supporting the weighing process through control of the following options: sliding weighing chamber doors, printout, zeroing, tarring etc. Especially appreciated wherever preventing the balance from soiling is important.

GLP Procedures

Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.

Pipettes Calibration

Function verifying correctness of piston pipettes functioning, the verification is performed via gravimetric measurement of the excreted liquid. Pipettes calibration may be either a stand-alone module or it may be operated

Air density correction

Function performing correction of mass measurement indication, wherein the air density is taken into account. It is used in balances with reading unit < 0,01 mg.

Ambient conditions monitoring

The possibility of cooperation with the THBR 2.0 system

Statistical Quality Control

Statistical control for determination of basic statistical criteria: maximum, minimum, standard deviation, mean values for each batch, etc.

ALIBI Memory

"ALIBI" memory enables saving and storing up to 100000 measurements. Measurements are saved automatically upon each pressing of the key. There is no need for any additional operations or changing settings.
The following data related with the measurements is saved: measurement date; measurement time; result (mass); tare value; operator carrying out the measurement (logged in); product name.
The software saves the measurement in a so called loop, i.e. when the measurement no. 100001 is saved, the measurement 1 gets automatically deleted from the memory.
Measurements saved to balance memory cannot be deleted.
You can preview and print out the data saved to the ALIBI database.

Documentation

Datasheet

Data Sheet

Show me

Download

Choose more product:
Show me

Show me

Download

User Manuals

User manual Web Editor

Show me

Download

(1.60 MB)