Home > Products > Pipettes Calibration > Manual Balances for Pipettes Calibration > XA 5Y.M.A.P Microbalance > XA 53.5Y.M.A.P Microbalance

This image is for reference only.

XA 53.5Y.M.A.P Microbalance

Product code: WL-112-0003

Change the model (5)

done

Max: 53gd: 1µg

⤢

ø26mm

expand_more

XA 6/21.5Y.M.A.P Microbalance

Max: 6 / 21gd: 1 / 2µg

⤢

ø26mm

XA 21.5Y.M.A.P Microbalance

Max: 21gd: 1µg

⤢

ø26mm

XA 21/52.5Y.M.A.P Microbalance

Max: 21 / 52gd: 1 / 5µg

⤢

ø26mm

XA 52.5Y.M.A.P Microbalance

Max: 52gd: 5µg

⤢

ø26mm

Maximum capacity [Max]: 53 g
Readability [d]: 1 µg

Select models:

✓ XA 6/21.5Y.M.A.P Microbalance

✓ XA 21.5Y.M.A.P Microbalance

✓ XA 21/52.5Y.M.A.P Microbalance

✓ XA 52.5Y.M.A.P Microbalance

✓ XA 53.5Y.M.A.P Microbalance

✓ Select all

Maximum capacity [Max]	53 g
Minimum load	0,1 mg
Readability [d]	1 µg
Verification unit [e]	1 mg
Tare range	-53 g
Standard repeatability [5% Max]	1,5 µg
Standard repeatability [Max]	6 µg
Standard minimum weight (USP)	3 mg
Standard minimum weight (U=1%, k=2)	0,3 mg
Permissible repeatability [5% Max]	2,4 µg
Permissible repeatability [Max]	8 µg
Linearity	±20 µg
Eccentric load deviation	20 µg
Sensitivity time drift	1×10⁻⁶/Year×Rt
Stabilization time	~ 3,5 s
Adjustment	internal (automatic)
OIML Class	I
Leveling system	automatic – Reflex Level System
Display	10″ graphic colour touchscreen
Weighing chamber doors	automatic
Delivery components	Microbalance, weighing pan, weighing pan shield, power supply, automatic pipette calibration adapter: (base, bottom ring, glass vessel, pipette calibration adapter, evaporation ring, weighing pan, glass lid, mechanical closing cover, protecting screw), brush, fabric dust cover.
Weighing chamber dimensions	199×170×217 mm
Capacity	11 ml
Weighing pan dimensions	ø26 mm
Packaging dimensions W x D x H	750×492×595 mm
Net weight	14,5 kg
Gross weight	18,9 kg
Protection class	IP 43
Communication interface	2×USB-A, USB-C, RS 232 (COM3), HDMI, Ethernet, Wi-Fi^®, Hotspot
Power supply	Adapter: 100 – 240V AC 50/60Hz 1A; 15V DC 2,4A Balance: 12 – 15V DC 1,4A max*
Operating temperature	+10 – +40 °C
Operating temperature change rate	±0,3 °C / 1 h (±1 °C / 8 h)
Relative humidity	40% – 80%
Relative humidity change rate	±1% / h (±4% / 8 h)

Additional fee
for verification

Repeatability is expressed as a standard deviation from 10 cycles of mass standard weighing.

Stabilization time dependson the ambient conditions and the dynamics of weighing pan loading; specified for FAST profile.

* The power supply can be connected to the socket on the back of the balance housing or to the terminal.

360°

Videos

Complete Solutions for Mass Measurement in Pharma Industry

Connecting RADWAG RTP-UEW80 Printer via Wi-Fi^® (Tutorial)

Talk to it. Voice Commands in New ELLIPSIS Balance by RADWAG

Remote VPN Support on ELLIPSIS Balances

ELLIPSIS – Unlimited Connections

310 ELLIPSIS – Scan or Tap to Log In

ELLIPSIS – New Balance by RADWAG

ELLIPSIS – Cutting Edge, Innovative, New

5Y Functions: Parts counting

Air Drafts Eliminated and Stabilization Time Reduced by 40%!

XA 5Y Unpacking and Installation (Tutorial)

RTP - The First Receipt Printer of RADWAG Production!

Statistical Quality Control

Calibration on a Laboratory Balance vs. Balance with a Steam Curtain – How to Install It?

Accurate and Easy Pipettes Calibration with the 5Y Balance!

What Interfaces do RADWAG Balances Have? Wi-Fi^®, USB, Ethernet, HDMI and More!

Discover Hotspot in RADWAG Balances

New Design of RADWAG Balances – Easy Cleaning

Precision and Working Comfort – Operating RADWAG Balances in Every Glove!

5Y Functions: Animal Weighing

5Y Functions: Statistics

5Y Functions: DWA®

5Y Balance and Barcode Scanner – Easy Connection

New Menu Language in 5Y Series Balances: Japanese

5Y Functions: Checkweighing

5Y Functions: Dosing

5Y Functions: Formulations

Percentage deviations

5Y Functions: Weighing

5Y Functions: Proximity Sensors – Touch-Free Control (Tutorial)

5Y Functions: GLP Procedures – Objective Documentation of Measurements (Tutorial)

Weighing Printout Design in Analytical and Precision Balances (Tutorial)

Easy Printing with Wi-Fi^® Thermal Receipt Printer by RADWAG.

New AS and PS 5Y Balances – Autotest (Tutorial)

Functions

Autotest

Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.

Percent Weighing

Percent Weighing function is used for comparision of measured products with mass standard. Mass of a mass standard may be a numeric value taken from a database or it may be determined through a measurement process. Each measured product is compared to mass standard, mass of which is presumed as a model 100% ideal mass. For products weighing less than the mass standard, obtained results are lower than 100%, for products weighing more, the obtained results are greatly exceeded.

Peak hold

Function registering the greatest temporary indication occurring in course of the weighing process. It is most often used in medical scales in order to hold the measurement indication.

Statistics

Statistiscs function registers and analyses performed measurements. This supplies the user withthe following information: Max and Min standard deviation, average value, variance, range et.

IR sensors

Programmable function supporting the weighing process through control of the following options: sliding weighing chamber doors, printout, zeroing, tarring etc. Especially appreciated wherever preventing the balance from soiling is important.

GLP Procedures

Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.

Pipettes Calibration

Function verifying correctness of piston pipettes functioning, the verification is performed via gravimetric measurement of the excreted liquid. Pipettes calibration may be either a stand-alone module or it may be operated

Air density correction

Function performing correction of mass measurement indication, wherein the air density is taken into account. It is used in balances with reading unit < 0,01 mg.

Automatic sliding door

Automatic side panes opened via touch-free IR sensors.

Moveable range

Dual range analytical balances can be equipped with much more precise measuring range but only in very limited part of max capacity and only from zero load. A new technology introduced by RADWAG allows for moving this limited range till max capacity of the balance is reached. Such solution has been named as: Moveable range.

Differential weighing

Differential weighing informs about mass variation a particular sample, wherein the said variation is a result of manufacturing processes.

Differential weighing is often applied in product control process, for which reference product parameters have been specified in order to be used as a source of comparison for the whole series.
Insuchcasestandard deviation is the information which tells about quality and completeness of a final product. For systems based on a feed-back technique such information may be used by control units.

Ambient conditions monitoring

The possibility of cooperation with the THBR 2.0 system

Replaceable unit

Weight function to change the weight unit.

Statistical Quality Control

Statistical control for determination of basic statistical criteria: maximum, minimum, standard deviation, mean values for each batch, etc.

ALIBI Memory

"ALIBI" memory enables saving and storing up to 100000 measurements. Measurements are saved automatically upon each pressing of the key. There is no need for any additional operations or changing settings.
The following data related with the measurements is saved: measurement date; measurement time; result (mass); tare value; operator carrying out the measurement (logged in); product name.
The software saves the measurement in a so called loop, i.e. when the measurement no. 100001 is saved, the measurement 1 gets automatically deleted from the memory.
Measurements saved to balance memory cannot be deleted.
You can preview and print out the data saved to the ALIBI database.