PS 200/2000. R2.HHassas Terazi

✆

Português (Brasil)Deutsch English Español Français Italiano Japanese (日本語)Polski Türkiye Česky USA

Scan model

Ana Sayfa > Ürün > Laboratuvar terazileri > Hassas Teraziler > R Serisi > PS 200/2000. R2.HHassas Terazi

This image is for reference only.

PS 200/2000. R2.HHassas Terazi

Ürün kodu: WL-221-1001

Modeli değiştirin (10)

done

Max: 200 / 2000gd: 0,001 / 0,01g

⤢

ø100mm

expand_more

PS 210.R2.H Hassas Terazi

Max: 210gd: 0,001g

⤢

ø100mm

PS 360.R2.HHassas Terazi

Max: 360gd: 0,001g

⤢

ø100mm

PS 600.R2.HHassas Terazi

Max: 600gd: 0,001g

⤢

ø100mm

PS 750.R2.HHassas Terazi

Max: 750gd: 0,001g

⤢

ø100mm

PS 1000.R2.HHassas Terazi

Max: 1000gd: 0,001g

⤢

ø100mm

PS 2100.R2.M.H Hassas Terazi

Max: 2100gd: 0,01g

⤢

195×195mm

PS 3500.R2.M.H Hassas Terazi

Max: 3500gd: 0,01g

⤢

195×195mm

PS 4500.R2.M.H Hassas Terazi

Max: 4500gd: 0,01g

⤢

195×195mm

PS 6100.R2.M.H Hassas Terazi

Max: 6100gd: 0,01g

⤢

195×195mm

Maksimum yük [Max]: 200 / 2000 g
Okuma doğruluğu [d]: 0,001 / 0,01 g

Modelleri seç:

✓ PS 200/2000. R2.HHassas Terazi

✓ PS 210.R2.H Hassas Terazi

✓ PS 360.R2.HHassas Terazi

✓ PS 600.R2.HHassas Terazi

✓ PS 750.R2.HHassas Terazi

✓ PS 1000.R2.HHassas Terazi

✓ PS 2100.R2.M.H Hassas Terazi

✓ PS 3500.R2.M.H Hassas Terazi

✓ PS 4500.R2.M.H Hassas Terazi

✓ PS 6100.R2.M.H Hassas Terazi

✓ Select all

PS 200/2000. R2.HHassas Terazi

PS R2.H serisi teraziler, hassas terazilerin standart seviyesini yeniden tanımlar. R serisi terazilerin bütün özelliklerini paylaşmakla beraber zorlu işletme koşullarında da (yoğunlaştırılmış toz, IP 54 için tipik olarak farklı açılarda aşağı düşen su damlaları) çalışırlar.

LCD ekran

Bu teraziler, bir ölçüm sonucunun açık ve okunaklı bir şekilde görüntülenmesini sağlayan yenilikçi LCD ekran ile donatılmıştır. Ayrıca, kullanıcıya, ürün ismi, dara değeri gibi ek mesaj ve bilgi sağlayan yeni bir metin satırı sunar.

Arabirimler

PS R2.H terazilerin ilave bir özelliği de, teraziden ayrı hermetik olarak kapalı gömülü ara birimidir. Arabirimler 2 × RS232, USB tip A, USB tip B ve isteğe bağlı Kablosuz Bağlantı içerir.

Terazinin gövdesi plastikten yapılmış olup kefesi paslanmaz çeliktendir.

Teknik Veriler

Maksimum yük [Max]	200 / 2000 g
Minimum yük [Min]	20 mg
Okuma içinğruluğu [d]	0,001 / 0,01 g
Dara aralığı	-2000 g
Minimum ağırlık (USP)	1 g
Minimum ağırlık (U=1%,k=2)	0,1 g
Standart tekrarlanabilirlik [Maks. %5]	0,0005 / 0,005 g
Tekrarlanabilirlik (Max)	0,001 / 0,01 g
Doğrusallık	±0,002 / 0,02 g
Kararlılık süresi	2 / 1,5 s
Ayarlama	dahili (otomatik)
Tesviye sistemi	manuel
Display	5,3” LCD (aydınlatma ile)
Tartım kefesi boyutları	ø100 mm
Ambalaj boyutları G x D x Y	475×380×345 mm
Net ağırlık	4,5 kg
Brüt ağırlık	6,5 kg
IP Sınıfı	IP 54
Haberleşme arayüzü	2×RS232¹, USB-A, USB-B, Wi-Fi^® (opsiyon)
Güç kaynağı	Adaptör: 100 – 240V AC 50/60Hz 0.6A Max; 12V DC 1,2A Teraziler: 12 – 15V DC 0,7A max; 3 – 5,5W*
Güç tüketimi	4 W
Çalıştırma sıcaklığı	+10 – +40 °C
Atmosferik nem	40% – 80%

Tekrarlanabilirlik, kütle standardının 10 yerleştirmesinin standart sapması olarak ifade edilir.
Kararlılık süresi dış koşullara ve kefeye yük yerleştirme dinamiklerine bağlıdır; FAST profili için belirtilmiştir.
¹Aksesuar olarak temin edilebilen barkod okuyucular, yalnızca RS232 arayüzünü kullanarak kantarla birlikte çalışır.

360°

Videolar

Complete Solutions for Mass Measurement in Pharma Industry

Connecting RADWAG RTP-UEW80 Printer via Wi-Fi^® (Tutorial)

PS R2 Precision Balance Unpacking and Installation (Tutorial)

RTP - The First Receipt Printer of RADWAG Production!

Wi-Fi^® özellikli RTP-UEW80 ile Kolay Baskı

R Series Laboratory Balances

Fonksiyonlar

Autotest

Diagnostic function aiming at metrological parameters determination (repeatability), the parameters are determined for the actual conditions of use. When speaking of repeatability it may be also used for weighing time optimization. Autotest is operated in an automatic mode thus operator’s time is saved.

Dosing

Weighing process for which reference mass has been determined together with tolerance for its determination. Dosing tolerance is given in [%] and it is calculated in relation to the reference value thus being a permissible deviation of this process. This solution is used for weighing powders, liquids and loose materials. Dosing function performance is often supported with bargraph - load indicator. For industrial scales it is possible to use a control systems of dosing process.

Percent Weighing

Percent Weighing function is used for comparision of measured products with mass standard. Mass of a mass standard may be a numeric value taken from a database or it may be determined through a measurement process. Each measured product is compared to mass standard, mass of which is presumed as a model 100% ideal mass. For products weighing less than the mass standard, obtained results are lower than 100%, for products weighing more, the obtained results are greatly exceeded.

Totalizing

Function adding new mass value to already obtained one. This allows to determine mass content of the mixture, being a composition of number of different consistence components. Totalizing is limited by maximum capacity parameter.

Parts counting

Function using mass measurement for determination of measured items quantity. Mass of a single item is required for this process. It may be either estimated through weighment or taken from a database. For items counting the following algorithm is used: all items mass / single item mass = quantity. Function operation is supperted by a mechanism of Automatic Correction of Accuracy. This allows to update single item mass in course of the process. To a certain extend Automatic Correction of Accuracy eliminates error which may be a result of different mass values of seemingly alike single elements. For industry solutions items counting may be simultaneously carried out with checkweighing and dosing thus industry solutions feature audio signalling base informing that specified number of items has been weighed. It is possible to apply weighing systems using few platfroms of different MAX capacities and different accuracies.

Peak hold

Function registering the greatest temporary indication occurring in course of the weighing process. It is most often used in medical scales in order to hold the measurement indication.

Statistics

Statistiscs function registers and analyses performed measurements. This supplies the user withthe following information: Max and Min standard deviation, average value, variance, range et.

Checkweighing

Checkweighing function is used for checking whether the measured sample mass is within the predefined threshold values, Low [LO] and Hgh [HI]. The thresholds are given in [g] and [kg] units. Current state of a sample being measured is signalled by means of pictorgams located on a display for laboratory balances, for industrial scales Stackligt System is used. This visual +/- inspection is in operation during segregation, control or packing process of products for which mass has bees determined with a specifaied tolerance, eg. 12860 g ± 5 g

Under-pan weighing

The solution enables weighing with use of a stand, which is advisable for loads of non-standard shapes and dimensions and those that generate magnetic field.

GLP Procedures

Diagnostic function allowing to objectively document performed measurements. GLP procedures may be either presented in a short report form or extended one.

Animal weighing

Process of mass determination for a product which may unwillingly reposition within the weighing pan. Mass determination in such cases requires much longer period of time when compared to typical weighing process. It is the user who defines period of time needed for control of measured product mass. The user can thus optimize the function depending on the measured product characteristics.

Density determination

Liquid or solid body density function uses the Archimedes principle and it requires a special kit to be applied. The kit when used, replaces a weighing pan. For solids mass of the sample must be determined first in the air, next in the liquid of specified density. For liquids the so called sinker, density of which has been determined, must be measured first in the air, next in the tested liquid. The density determination process is disturbed by air bubbles which may stick either to the measured sample or the sinker. In case of laboratory equipment very light solids may be measured. For industry, solid bodies density may be determined by means of under-pan weighing. Tested load of significant size may be measured this way.

Dokümantasyon

Teknik Veri Sayfası